Bore Alignment Service

Bore alignment is an important step during engine machining or the installation rotor after balancing or other rotor services. This step will establish a perfectly straight bore in the crankcase and cylinder block as standard tolerance. Bore alignment and measurement are vital jobs for any maintenance machine.

WHY IS MAIN BORE ALIGNMENT IMPORTANT?

Alignment of the main bores is an important role because its position establishes the centerline for the crankshaft, and how the crank aligns with the cylinder heads, decks, and camshafts. If the bores are not aligned properly, the main bearings can usually be machined or honed to restore alignment and size.

Bore Alignment

Bore Alignment

Bore Alignment

Bore Alignment

CYLINDER BLOCK LINE BORE ALIGNMENT

When referring to cylinder heads, the term line boring refers to the main bearing housin¬gs but it can equally refer to camshaft housin¬gs where the camshaft is located inside the cylinder head. The line boring operation restores both the size and alignment of these hous¬ings so that the rotating components (cams or cranks) turn freely.

With cylinder blocks, one of the most common reasons for needing a line bore is after a crankshaft has failed. A badly worn cranking shaft can “whip” within the main bearing housing distorting them. A seized crankset (due to lack of lubrication or pressure) can result in the chainrings locking into place on the crankset resulting in them being forcibly turned by the chainring teeth which causes distortion and wear.

Similarly, if a seizure occurs inside the camshaft housing where the cam bushes are located, they could be damaged or even rotate within the block itself, causing serious damage. This could result in damage to the housing which would require the housers to be bored oversized, removing the damage and realigning them. Corresponding oversized bushes will be needed to completely repair the damage.
In high-performance vehicles, strength in the cranking shaft area can be improved by installing steel main bearing caps. These will be provided in a semi-finished state and may require some line boring to ensure perfect final alignment before installation.

All or any of the above could mean that your casting needs to be line bored.

Jika ada kebutuhan Bore Alignment service atau shaft alignment, silahkan menghubungi kami di sales@gammaenergi.com atau klik di sini

 

Kalibrasi & Repair Fluke Ti400 Infrared Camera

Untuk memastikan alat /kamera Fluke infrared berfungsi dengan baik dan akurat, maka kalibrasi & repair Fluke Ti400 dan kamera tipe lainnya merupakan sesuatu yang penting dilakukan. oleh karena itu, kami membantu dalam melakukan kalibrasi & repair Fluke Ti400 dan kamera infrared lainnya. Silahkan menghubungi kami di 081513166131 atau sales@gammaenergi.com

———————-

Powerful high-performance features make troubleshooting fast and easy.

Technology changes. The last thing we want is for you to feel like you’re missing out on critical innovations, so Fluke has engineered the Ti400 infrared camera to adapt to change.

Being future-ready is part of its DNA. You can test and measure with wireless speed and ease and connect with other wireless devices. If there’s an infrared camera in your future, make sure it’s one with a future.

Auto Focus Redefined

Get an in-focus image like never before with the touch of a button. LaserSharp®  Auto Focus, exclusive to Fluke, uses a built-in laser distance meter that calculates and displays the distance to your designated target with pinpoint accuracy. Other auto focus systems may focus on the surrounding landscape or closer targets and compromise an in-focus and your ability to get accurate temperature measurements.

On target and in-focus. Every. Single. Time.

Capture up to five additional measurements wirelessly.

A free firmware update to help find problems fast will allow you to capture up to 5 additional measurements by enabling the CNX™ Wireless system* on your thermal imager. These additional measurements help diagnose problems faster and provide additional data to create more comprehensive reports.

Field installable telephoto and wide angle lenses are available for added versatility for special applications and voice annotation makes pen and paper no longer necessary.

As always, Fluke SmartView® software is included at no additional charge.

Kalibrasi & Repair Fluke Ti400

Main Feature

  • High performance, 320×240 thermal imaging camera for maintenance professionals
  • Features LaserSharp® Auto Focus to produce consistently in-focus images.
  • Offers Fluke Connect® App to share results with remote users via a smartphone
  • Measures temperaturesfrom-20 °C to +1200 °C (-4 °F to +2192 °F)
  • Provides IR Fusion® technology with AutoBlend™ mode to help clearly identify potential problems with precisely blended visual and infrared images
  • Provides a one-handed, easy-to-use interface
  • Offers faster communication with wireless image transfer directly to PC, Apple® iPhone® or iPad®
  • Includes backlit ruggedized LCD capacitive touchscreen Captures additional digital images to show location or additional site details with IR-PhotoNotes™ photo annotation system
  • Digitally documents critical information along with the infrared image using IR-PhotoNotes™ or voice annotation
  • Works with optional interchangeable lenses for greater flexibility in additional applications
  • Includes rechargeable, field replaceable smart batteries with five-segment LED display to show charge levels
  • Captures high definition visible light images with built-in 5-megapixel industrial performance digital camera
  • Includes Fluke Connect® SmartView® Analysis and Reporting Software

Kalibrasi & Repair Doble TDR9100

Kami membantu dalam proses Kalibrasi & Repair Doble TDR9100 Circuit Breaker Test System dengan output sertifikat kalibrasi dari manufactur / pabrikan. Dengan pengalaman dan dukungan dari pihak pabrikan, Kalibrasi & Repair Doble TDR9100 Circuit Breaker Test System dilakukan dengan kualitas terbaik.

The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.

The Doble TDR9100 provides measurements for main and auxiliary contact timing, mechanical motion analysis, analog values, resistance and capacitance.

Use this inclusive, rugged and field-portable instrument for simple and complex testing of circuit breakers.

The TDR9100 controls circuit breaker trip and close commands and supports the following operations: Trip (O), Close (C), Reclose (O-0.3s-C), Tripfree (CO), O-CO, O-0.3s-CO, First Trip (O), Slow Close (C).

Features

  • Features up to 4 breaks per phase, 3 motion channels, and 6 event channels
  • Testing Flexibility – the TDR9100 can be ganged as a set of 2 or 3 units effectively doubling or tripling your usable channels and main contacts for up to 12 breaks per phase
  • User-friendly T-Doble Software features an intuitive control panel for quick, efficient and simple testing of circuit breakers
  • Measure additional parameters in the mechanism cabinet using Doble or 3rd party transducers

Benefits

  • Know that your breakers can and will perform when they are needed
  • Easily detect main contact and resistor contact timing errors
  • A patented digital rotary and linear transducer provide early diagnosis of mechanical problems
  • Immune to Interference – the accuracy of test results is unaffected by the severe conditions of electrostatic and electromagnetic interference that are normally present in harsh substation environments.
  • Control with a Doble Universal Controller (DUC), tablet or PC

Jika ada kebutuhan kalibrasi atau repair produk dari brand DOBLE atau brand lainnya silahkan menghubungi kami di 081513166131 atau email ke sales@gammaenergi.com

Rental Omicron CP TD-1 – Tand Delta /Power factor Test Equipment

Untuk pengetestan Tan Delta Perlatan dan Pengetest-an trafo, kami menyediakan rental Omicron CP TD-1 – Tand Delta /Power factor Test Equipment. Informasi harga dan lead time, silahkan menghubungi sales@gammaenergi.com atau 081513166131

Product Details

Combined with the Omicron CPC 100 Multi-Functional Primary Test System, the Omicron CP TD1 Capacitance/Dissipation Factor Testing Device (Tan Delta) measures the capacitance and dissipation factor (power factor) with laboratory precision. 

This allows the insulation condition of transformers, generators and other parts of high-voltage systems to be tested according to IEEE 62 (C57.152), IEC 60076-1 and -3, as well as the CIGRE “Guide for Transformer Maintenance”. As recommended in the CIGRE Guide, testing is performed at variable frequencies to better diagnose signs of aging in insulation.

Key features

  • Compact and rugged all-in-one test set
  • Wider frequency range for more sensitivity (15 Hz – 400 Hz)
  • Testing at variable frequencies for better condition diagnosis
  • Excellent suppression of mains frequency interference fields
  • High-voltage source for partial discharge measurements up to 15 kV
  • Portable component and simple to transport using a trolley

Applications

  • Power transformers
  • Rotating machines
  • Current transformers
  • Voltage transformers
  • High-voltage (HV) cables
  • Gas-insulated switchgear (GIS) systems

Jika ada kebutuhan rental Omicron CMC 356, silahkan klik di sini

Kalibrasi Fixture Laser Alignment

Dengan dukungan manufacture, Kami memberikan layanan Kalibrasi Fixture Laser Alignment untuk memastikan peralatan yang digunakan masih dalam kondisi baik dan layak digunakan.

Informasi Jasa kalibrasi fixture laser Alignment serta jasa rental Rental vibration calibrator Modalshop 9110D, silahkan menghubungi sales@gammaenergi.com atau 0815-1316-6131

NXA Pro

It is a shaft alignment revolution

A revolution in shaft alignment as well as a revolution in usability with the  NXA Pro – a digital laser based shaft alignment system!

The NXA Pro aims to provide the user with a fast and simple operation, as well as access to advanced functions and capabilities, such as the OmniView™ and the VertiZontal Moves™, and probably the best power management system in the marketplace.

Kalibrasi Fixture Laser Alignment

OmniView™

The graphical user interface is shown off on a 6,5” transflective display screen with icons and symbols to guide you, in other words, no text is involved.

The adaptive user interface will guide you throughout the measurement and alignment process.

We have fitted the NXA Pro with gyros and can, therefore, adapt the screen view from the same side that the user is positioned – our OmniView™ function, i.e. the system knows where it is in relation to the machine.

VertiZontal Moves™

The adaptive user interface will guide you throughout the measurement and alignment process. We are especially proud of the function – VertiZontal Moves™ – where you only have to measure once before making the required vertical and horizontal adjustments. Quite a time conserver in a time strained maintenance world!

Power management system

The NXA Pro has a power management system that will make your life so much easier! The display unit has a 10-hour continuous battery operating time, and should the need arise during an alignment job; the display unit can be express charged to an 80% capacity in one hour. The sensor units will last for 24 hours minimum thanks to the long-life batteries.

Rental Easy Laser Alignment

Dalam melakukan perawatan terutama alignment mesin-mesin, diperlukan perlatan yang presisi, canggih serta mudah digunakan. Untuk memenuhi kebutuhan akan peralatan yang sesuai kebutuhan dilapangan, kami menyediakan jasa Rental Easy Laser Alignment.

Rental Easy Laser Alignment

Beberapa hal yang bisa menjadi pertimbangan kenapa memilih Rental Easy Laser Alignment

  • Easy to learn and to use.
  • Compact measuring units for use on most machine designs.
  • All wireless units (Built-in Bluetooth® technology and integrated rechargeable battery).
  • Large 5.7″ color display.
  • Programs with both symbols and text = easy to understand.
  • TruePSD technology with unlimited resolution.
  • Dual PSD, dual laser beams, and dual inclinometers for superior control and accuracy.
  • Produce PDF reports directly from the Display unit and save to USB memory.
  • Fast service and support. 48-hours Express service if necessary.
  • Low overall costs during the entire lifecycle of the product, for example, servicing, accessories, etc.
  • Expandable / Adaptable. A range of accessories means that you can adapt the measurement system to your needs, now and in the future

Laser® E540 is a very powerful shaft alignment system in which the program guides user step-by-step with both icons and text makes the system very easy to use for everyone, regardless of prior knowledge. The E540 system includes measurement programs for horizontal machines, vertical machines, and alignment of machine trains with three machines. The measuring units are pre-mounted for rapid machine set-up. Start with the measuring units positioned anywhere through 360 ° around the shaft, then take any three readings down to 20° in-between. Then adjust the machine with the live values in both horizontal and vertical directions. A PDF report is generated automatically when the measurements are saved. Simple and efficient!.

The shaft alignment system has a large 5.7″, bright color display that clearly shows all the steps of the measurement. The measuring units have TruePSD-technology, which gives unlimited resolution. Twin laser beams, twin PSDs and twin inclinometers give you superb control of the measurement in all situations. The measuring units are incredibly compact featuring Bluetooth® Wireless technology, an integrated rechargeable battery, and large 30 mm TruePSD detectors. This means that they are easy to install on most types of machines, even where there is limited space. The wireless technology gives you full freedom of movement around the machine that is to be aligned. Display units, measuring units and fixtures are all very robust for the highest accuracy in demanding industrial environments.

Includes:
– Display unit E-series E52
– Measuring unit S
– Measuring unit M
– Shaft bracket with chain
– Chain 900 mm
– Set of rods (4x 60 mm)
– Rod 120 mm
– Strap for Display unit
– Measuring tape 3m
– Cable USB A to B 1,8m
– Battery Charger (100-240 V AC)
– DC Split cable,for charging
– DC to USB adapter, for charging
– Case Plastic Shaft E530

Jika ada kebutuhan peralatan laser alignment brand pruftechnik, bisa hubungi kami.

Jasa Pengukuran Tan Delta

Setiap peralatan listrik yang beroperasi pastilah mengalami stres terhadap faktor tegangan operasi, vibrasi, temperatur, kotoran dan lain sebagainya. Semua faktor tersebut akan menyebabkan penurunan ketahanan isolasi peralatan listrik secara terus menerus. Untuk mengetahui kondisi ketahanan isolasi tersebut perlu dilakukan jasa pengukuran tan delta

Dalam sebuah jaringan sistim tenaga listrik yang komplek, penurunan atau penuaan tahanan isolasi peralatan listrik merupakan suatu masalah serius yang dapat menimbulkan kerugian yang besar seperti kerusakan transformator, meledaknya Circuit Breaker dll.
Untuk menghindari breakdown peralatan yang tidak terduga dan kestabilan distribusi power sangatlah penting untuk mengetahui kondisi isolasi peraltan tersebut dan memonitor secra berkala untuk mendapatkan degradasi ketahanan isolasi.

Dalam sistim kelistrikan, Disipasi Fakor atau Pengukuran Tan Delta bertujuan untuk mengetahui kualitas isolasi suatu peralatan listrik. Oleh karena itu, suatu peralatan listrik yang baru perlu diketahui hasil uji tangen delta-nya yang nantinya berguna sebagai referensi untuk pengukuran tangen delta berikutnya yang dilakukan secara berkala, sehingga didapat grafik degradasi tahanan isolasi peralatan tersbut. Grafik hasil uji tanden delta tersebut akan memperlihatkan efek penuaan tahahanan isolasi suatu peralatan  mulai dari awal pembuatan sampai selama pengoperasian. Dengan data ini, dapat ditentukan kapan dilakukan pemeliharaan, penggantian peralatan tersebut secara terencana, sehingga kerusakan secara tidak terduga dapat ditekan. Hal inipun menjamin keamanan dan kestabilan supplay listrik.

Dengan kebutuhan tersebut di atas, kami memberikan jasa pengukuran tan delta baik peralatan berdasa kecil atau generator dengan daya 45 MW ke atas.

Pada pengukuran Tan Delta tersebut, kami mengguakan Omicron CPC 100 TD dan juga menggunakan Megger Delta 4000 series.

Pengkuran Tan Delta menggunakan Omicron CPC 100 TD

 

Kalibrasi Olympus Nortec 600D

Kami membantu customer dalam melakukan kalibrasi Olympus Nortec 600D dengan output sertifikat kalibrasi dari manufactur (Olympus). Dengan Kalibrasi Olympus Nortec 600D secara periodik, customer akan mendapatkan kepastian mengenai hasil pengukuran alat tersebut.

Kalibrasi Olympus Nortec 600D

Olympus converges its latest advancements in high-performance digital circuitry and eddy current flaw detection into one compact and durable portable unit—the new NORTEC® 600. With its crisp and vivid 5.7 inch VGA display and true full-screen mode, the NORTEC 600 is capable of producing highly visible and contrasting eddy current signals in any lighting condition.
The redesigned interface of the NORTEC 600 borrows the intuitive, knob-operated navigation of its NORTEC predecessors and combines it with the simple menu structure and highly efficient direct-access keys of other popular Olympus instruments. Available in four versatile models, the NORTEC 600 offers a wide range of innovative functionalities, including an Application Selection menu, an all-in-one display, real-time readings, and signal calibration in Freeze mode, ensuring that inspections are quick and easy for any level of operator.

Reliable and Robust
Based on an already field-proven instrument case, the NORTEC 600 is built for endurance in harsh field conditions. Its casing’s durability and resistance to extreme weather makes the NORTEC 600 an instrument you can trust for any eddy current inspection job.

Key Features
Designed to meet the requirements of IP66.
EN-15548 compliant.
Long battery life (up to 10 hours).
Bright, 5.7 inch (14,5 cm) VGA display.
Full-screen option in any display mode.
Improved filters for rotary scanner mode.
Intuitive interface with Application Selection presets.
All-settings configuration page.
10 Hz to 12 MHz frequency capacity.
Automatic internal balancing (BNC connector).
Up to two real-time readings.
True automatic mixing.
Storage capacity of up to 500 files (program and data).
On-board file preview.

Versatility and Compatibility(Highest-end Nortec 600D Model in Listing)
The NORTEC® 600 is available in four versatile instrument models to meet the widest range of inspection needs. From the basic model upward, each unit unlocks more features. For maximum convenience, additional features can also be unlocked remotely

Portable and Lightweight
The NORTEC 600 weighs only 1.6 kg and is delivered with a factory-installed hand strap that provides direct thumb access to the key controls, offering genuine handheld versatility to operators.

Two Probe Connectors
All models of the NORTEC 600 come with the standard LEMO 16-way universal connector, as well as a BNC connector for absolute probes. Simply select the connector in the instrument interface. When reading from the BNC connector, the instrument features automatic internal balancing for hassle-free operation.
The 16-way LEMO connector also supports the PowerLink NORTEC technology, which features automatic probe recognition and instrument presets for quicker setups.

Compatible with Current Procedures and Other Manufacturers
To simplify inspection, the NORTEC 600 includes all the legacy modes and layouts used in existing NORTEC-specified procedures, as well as those used by many other equipment manufacturers. Standard impedance plane view, sweep mode (strip chart), split screens, adjustable null point, crosshairs, improved filter response, reference signal display, and several other useful features are all part of the NORTEC 600 package.
Offering compatibility with many other probe and rotary scanner manufacturers, the NORTEC 600’s accessories include cables and adaptors such as a 12-way LEMO, an 11-way Fischer, and more. The proper adaptor or scanner cable make it possible to benefit from all the outstanding capabilities of the NORTEC 600, without investing heavily in probes and accessories.

One of the Most Brilliant Displays in the Industry
Vibrant VGA Display

The NORTEC® 600 has one of the most brilliant displays available on the portable eddy current flaw detector market. The unique brightness, resolution, and definition of its 5.7 inch VGA display makes it possible to interpret eddy current signals at a distance. The user-selectable color schemes ensure that the display is equally clear and easy-to-read whether you are using the NORTEC 600 indoors or outside. 

True Full-Screen Display
In addition to impressive size and brightness, the NORTEC 600’s VGA display also features a new full-screen mode that can be activated at the touch of a key.
Available for all applications and in all display modes, the full-screen mode really comes in handy when reading signals over an extended period of time.
Depending on your NORTEC 600 model, you can choose between the following displays:
  -single impedance plane.
-dual impedance plane.
-sweep (strip chart).
-split screen (sweep + impedance).
-waterfall.
-dual impedance plane.
-all-in-one display featuring up to 3 configurable traces.

For other calibration service for instrument, please check here

Kalibrasi dan Repair Flir Camera

Dalam meningkatkan keakuratan peralatan predictive maintenance, kami menyediakan jasa Kalibrasi dan Repair Flir Camera berbagai tipe baik tipe T, E atau tipe yang lain. Dengan support dari manufacture, jasa Kalibrasi dan Repair Flir Camera memberikan tingkat kehandalan yang tinggi serta delivery time yang cepat

FLIR cameras are designed and factory calibrated for accurate temperature measurements and thermal imaging. When maintained with FLIR’s annual calibration services, they will be highly reliable in spotting thermal anomalies and other temperature phenomena. Without proper maintenance and calibration, accurate measurements cannot be assured.

Kalibrasi dan Repair Flir Camera

14-Point Inspection & Calibration Program

FLIR´s exclusive 14-Point Inspection & Calibration program uses temperature references that are calibrated annually and traceable to the SP Technical Research Institute of Sweden, and the National Institute of Standards and Technology (NIST). The program includes the following steps:

FLIR 14-Point Inspection & Calibration Program:

  1. Perform a complete operational check
  2. MSX® calibration and laser alignment, when applicable
  3. Verify all internal cable and PCB connections
  4. Clean viewfinder and check optics
  5. Upgrade internal camera software to latest revisions
  6. Perform minor repairs
  7. Verify and/or re-equalize as needed each temperature range for image uniformity
  8. Verify standard lens calibration (others or special engineered lenses, optional)
  9. Verify ambient temperature compensation as needed
  10. Re-calibration to ensure it meets factory specification
  11. Calibrate temperature ranges up to +1,500°C, when applicable
  12. Perform quality approved acceptance test procedure
  13. Provide calibration label with next due date

This calibration output is Calibration Certificate from manufacture (Flir). if you need more information about other calibration services such as calibration Emerson CSI 2130 / 2140 or Flow meter, please contact us at sales@gammaenergi.com or 0815-131-66-131

Rental Vibration Analyzer CSI2130

Kami memiliki unit Rental vibration analyzer CSI2130 sebagai solusi bagi customer yang membutuhkan peralatan vibrasi yang handal, presisi dan user friendly serta memiliki fitur yang membantu dalam analisa kerusakan mesin. Jika membutuhkan jasa rental vibration analyzer CSI2130, silahkan menghubungi kami di sales@gammaenergi.com

Rental Vibration Analyzer CSI2130

Maintenance departments today are asked to run with fewer staff and smaller budgets than ever before. In this do-morewith-less environment, maintenance personnel can’t afford to continuously chase the next breakdown. They need to quickly and accurately identify developing faults and find the root cause of the machinery problem so that it can be fixed.  An effective technology solution must be simple to operate – reducing training requirements – while providing fast, actionable information to help you prioritize maintenance activities. Before CSi 2140 released, Emerson’s CSI 2130 Machinery Health Analyzer was developed with these requirements in mind. The CSI 2130 stands alone as the industry-leading vibration data collector. In addition, the CSI 2130 can provide:

  • Advanced vibration analysis
  • Cross-channel analysis
  • Transient analysis
  • Dynamic balancing
  • Laser shaft alignment
  • Motor monitoring

Portable and Durable
The durability of this unit makes it ideal for field work in a
wide variety of industrial applications.

  • Large Color Display: backlit VGA display for use anywhere.
  • Small and Lightweight: easily carried on long routes
  • In-Field Reports: color-coded alarm report for each point.
  • Industrial Design: IP 65 rated with optional safety rating.

So, rental CSI 2130 vibration analyzer is the solution for vibration analysis and condition monitoring. For rental CSi 2140 you can contact our office or send email to sales@gammaenergi.com

Contact Us On WhatsApp